Henny-penny OFE/OFG-322 Manuel d'utilisateur

Model OFE/OFG-321,322,323,324 SECTION 2. MAINTENANCE 2-1. INTRODUCTION This section provides procedures for the checkout and replac

Model OFE/OFG-321,322,323,324 2-9. IGNITOR MODULE During normal operation, the ignition modules send 24 volts to the ignitors and gas

Model OFE/OFG-321,322,323,324 2-11. I/O POWER SUPPLY BOARD ASSEMBLY The input/output power supply board assembly distributes

Model OFE/OFG-321,322,323,324 2-12. VACUUM SWITCH (Continued) 5. Using a Phillips head screwdriver, remove the screws sec

Model OFE/OFG-321,322,323,324 2-14. DRAIN MICROSWITCH Upon turning the drain handle, the drain microswitch circuit should op

Model OFE/OFG-321,322,323,324 2-15. FILTER SWITCH (Continued) 2. Remove the control panel above the switch.

Model OFE/OFG-321,322,323,324 2-16. GAS CONTROL VALVE ASSEMBLY (Continued) 3. Using a 7/16 inch wrench, remove the

Model OFE/OFG-321,322,323,324 2-16. GAS CONTROL VALVE ASSEMBLY (Continued) 7. With the bracket dropped down, re

Model OFE/OFG-321,322,323,324 2-17. BLOWER MOTOR ASSEMBLY (Continued) 4. Remove wire nuts connecting blow

Model OFE/OFG-321,322,323,324 2-17. BLOWER MOTOR ASSEMBLY (Continued) 8. Using 3/8 inch nut driver, remove

Model OFE/OFG-321,322,323,324 2-18. HEATING ELEMENTS (ELECTRIC ONLY) (Continued) 3. Perform an ohm check on one

Model OFE/OFG-321,322,323,324 2-3 HIGH TEMPERATURE LIMIT CONTROL (Continued) 3. Remove the two nuts securing the hig

Model OFE/OFG-321,322,323,324 2-18. HEATING ELEMENTS (ELECTRIC ONLY) (Continued) 9. Evenly space the element spr

Model OFE/OFG-321,322,323,324 2-19. HEATING CONTACTORS (ELECTRIC ONLY) Each well of an electric fryer requires t

Model OFE/OFG-321,322,323,324 2-19. HEATING Checkout (Power Supplied) CONTACTORS (ELECTRIC ONLY) (Co

Model OFE/OFG-321,322,323,324 2-20. SPEAKER ASSEMBLY (Electric Units) The speaker assembly emits audible signals to let the

Model OFE/OFG-321,322,323,324 2-21. HIGH TEMPERATURE 1. Drain the shortening from the frypot. LIMIT CONTROL (Ele

Model OFE/OFG-321,322,323,324 2-21. HIGH TEMPERATURE LIMIT CONTROL (Electric Units) (Continued)

Model OFE/OFG-321,322,323,324 2-22. AUTOLIFT ACTUATOR (MOTOR) REPLACEMENT (if applicable) (Continued) 5. Di

Model OFE/OFG-321,322,323,324 2-22. AUTOLIFT ACTUATOR (MOTOR) REPLACEMENT (if applicable) (Continued) 9.

Model OFE/OFG-321,322,323,324 2-23. AUTOLIFT 1. Remove electrical power supplied to unit. TRANSFORMER REPLACEMENT

Model OFE/OFG-321,322,323,324 2-24. AUTOLIFT PC BOARD REPLACEMENT (if applicable) (Continued) 4. Using a Philli

Model OFE/OFG-321,322,323,324 2-3 HIGH TEMPERATURE LIMIT CONTROL (Continued) 5. Remove the bracket from the heat tube cove

Model OFE/OFG-321,322,323,324 2-4. COMPLETE CONTROL PANEL REPLACEMENT Should the control board become inoperative, follow thes

Model OFE/OFG-321,322,323,324 2-5. POWER SWITCH (Continued) 4. With control panel removed, and the wires off the switch, p

Model OFE/OFG-321,322,323,324 2-6. TEMPERATURE PROBE REPLACEMENT (Continued) ELECTRIC GAS 2-6

Model OFE/OFG-321,322,323,324 2-6. TEMPERATURE PROBE 7. Tighten the compression nut hand tight and then a half turn REPLACEMENT

Model OFE/OFG-321,322,323,324 2-7. FLAME SENSOR The flame sensor recognizes the pilot flame and allows gas to (Gas Units)

Model OFE/OFG-321,322,323,324 2-8. PILOT / IGNITOR The Henny Penny open fryer (gas) has electronic spark ignition ASSEMBLY